I was able to do a loopback with no problems at all. Can you try the Card and Tool in another PC. Check you have the correct resources set Windows always gets my network cards IRQ wrong on a fresh install but if you believed windows everything is fine. That’s not a good sign then that the card is not detected. Setting it manually to what I know is correct gives me a warning about changing resources but everything works suddenly I’m not familiar with that particular card but I’m guessing the driver disk has a setup program where you assign IRQ plus less important stuff like frame type, etc or try another PCI slot and hope plug and play assigns it another one. Caluser Yes, that’s the exact card that I’m using. Last edited by Caluser on
|Date Added:||9 July 2018|
|File Size:||35.65 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
I’ve tried the stock drivers that came with Windows 95 and the drivers from online and different configurations.
Also do you have another card you can use? Board index All times are UTC.
This disclaimer is brought to you thanks to llan BSA. Setting it manually to what I know is correct gives me a warning about changing resources but everything works suddenly I’m not familiar with that liknsys card but I’m guessing the driver disk has a setup program where you assign IRQ plus less important stuff like frame type, etc or try another PCI slot and hope plug and play assigns it another one.
Or maybe, recove all other Cards you dont need for Dos and try Setup again.
VOGONS • View topic – Trying to set up Linksys Ether16 LAN Card Non-PNP
I Can’t help wondering if it could be a clock dependency of some sort – i. Could be just a duff card, it happens. I’ve pretty much given up on the Ether Have the SB16 and Yamaha sound card installed alongside. Though, I do know that it detects it under Windows just fine. Strange, given it is an NE clone. I’ve installed etehr16 into lijksys system and it seems to be working fine.
Looking for vintage computers and parts. In addition, it also does have a tendency to not even initialize properly under Windows in some cases whenever I make hardware changes to the system and NOT even touch the network card at all.
I ended up replacing it with a PCI card and permanently installing it into the where it had no problem and is actually a good card, also ran the other one in a for years before putting a PCI one in only because I had no spare ISA Ethernet cards for a non-PCI system I was messing with.
I’m beginning to think that it could be some linjsys of resource conflict, even though Windows doesn’t suspect it and that the SB16 is not even using it.
Linksys LNE2000 – Ether16 Combo LAN Card
Is this the card? PM me if you have some to give away. Last edited by Caluser on Still couldn’t get an IP address from the router and couldn’t do a loopback that way. Just use the NE Still can’t connect to the network.
Linksys ETHER16 LAN ISA Network Card With Coax Ethernet Connector | eBay
Did a little further testing. Users browsing this forum: Unfortunately, I couldn’t get very far to installing the utility software as it doesn’t detect the card, even in Pan and DOS with the packet driver successfully installed. You do not have the required permissions to view the files attached to this post.
Unrelated but it’s probably a good time to mention there was a Winsock update for Windows 95 as well- http: My 3C exhibits similar behavior in one of my ‘s if I ramp up the BUS Clock and the configuration tool will either not detect it or permanently damage the card. Now the lunksys problem is trying to get an IP address, which it won’t egher16. Caluser Yes, that’s the exact card that I’m using.
Linksys ETHER16 LAN ISA Network Card With Coax Ethernet Connector
It appears that even though MPU on the SB16 is set at and is disabled, the Ether16 still complains and doesn’t initialize. I was able to do a loopback with no problems at all. This site hosts no abandonware.
If you are lucky, the network card will have jumpers, otherwise ethed16 a case of trial and error to find the IRQ and IO base settings.